• Inspect and evaluate the condition of the

  • overall roof

  • sealants and joints

  • roof vents, air conditioners, antenna, and other roof components ​​

• Inspect and evaluate front and rear caps

  • aging and general overall condition

  • appearance and functional condition of the end caps, sidewalls, entrance doors, windows and cargo access doors.

  • any damage, discoloration and delamination of the side wall and end cap components.

• Identify and evaluate the types of slide-out room drive systems and the condition of the

  • roof material for the slide-out room

  • seals, sweeps, and gaskets for possible damage

  • attached wiring and utility harness that feed underneath the slide-out room

• Inspect and identify the operational type (manual vs electric) of the awnings , slide-out toppers and window awnings and operate and rate the condition of the

  • awning frames and latching mechanisms

  • fabric material of the awnings

  • Measure and document the fabric size of the awnings

• Inspect the condition of the 7 pin connector cord

• Operate and evaluate the emergency break away switch

• Activate and evaluate the operation of the DOT lights mounted on the RV

• Inspect and rate the condition of the power cord and its connection ends

• Remove cover panel of the 120 volt circuit breaker box to visually inspect the condition of the wiring, circuit breakers, and grounding connections.

• Verify the separation of all the wiring types

• Test and verify the output operation of the 120 VAC to 12 VDC converter for charging of the deep cycle battery

• Test and verify the inverter if applicable

• - if installed *strongly recommend performing oil analysis to determine internal combustion engine component condition.

• Identify and note the model, serial number, and run hours of the generator

• Check oil level

• Start and operate the onboard generator

• Test the voltage output and frequency (60 cycles)

• Put generator under a load to verify operation (typically operating 1 air conditioner will create the correct amount of load)

- if installed on this model of Generator *strongly recommend performing coolant analysis to determine the condition of the coolant fluid and the internal cooling system.

• Location of the radiator and cooling fans

• Visually inspect the coolant reservoir, radiator and hoses

• – if installed

• Identify and note the model and serial number of the inverter

• Visually inspect the wiring and electrical connections and fuses/circuit breakers

• Place electrical load on inverter to verify proper operation

• (12 volt DC deep cycle Battery Electrical System)

• Locate and note the location of the battery stack

• Evaluate the condition, age, and matched sizing of the battery stack

• Evaluate and determine if positive and negative cables are correctly matched for balanced load

• Access and visually inspect the wiring, fuse panel, and fuses of the 12 volt DC electrical system

• Evaluate the operation of the fresh water/wastewater monitor panel for incorrect tank readings

• (Gray and Black Water)

• Operationally test and inspect waste (gray and black) plumbing systems for leaks

• Identify the type of drain valve controls, verify they will maintain water in their tank, and test for ease of operation

• Verify the drain cap is in place and will hold wastewater

• - if equipped

• Document the manufacture date, location(s), and tank sizes of DOT cylinders

• Conduct visual inspection of exterior of cylinder for rust and other damage

• - if equipped

• If tank is visible, conduct a visual inspection of tank for rust or physical damage

• List the location, manufacture date (if accessible), and gallon capacity of the tank

• Identify and note the brand and type of system

• Verify the system operates properly by extending and retracting leveling system

• Note visual indications of hydraulic leaks or mechanic issues

• Identify and document the Vehicle Identification Number (VIN), Vehicle Frame Number and license plate info

• List the inspection sticker information (if applicable), RVIA inspection seal number, Gross Vehicle Weight Rating, and date of manufacture

• Please note the following items: Due to insurance restrictions the Motorhome can NOT be driven by the Inspector

• *strongly recommend performing oil analysis to determine internal combustion engine component condition.

• Make and model of the engine

• Verify oil level on the dipstick

• Indications of engine issues or any noises while running

• Are there noticeable oil or exhaust leaks

• Note the oil pressure reading on the dash gauges

• *strongly recommend performing coolant analysis to determine the condition of the coolant fluid and the internal cooling system.

• Location of the radiator and cooling fans

• Visually inspect the coolant reservoir, radiator and hoses

• *strongly recommend performing transmission fluid analysis to determine the condition of the fluid and the internal components of the transmission.

• Type of transmission

• Fluid level on dipstick

• Indications of contaminated transmission fluid

• Visually inspect for bent or damaged components and hydraulic leaks

• Perform and document LP gas timed leak test

• Test the Ground Fault Circuit Interrupter (GFCI) circuits

• Test all wall receptacles for correct polarity and ground fault

• Test the exterior skin for hot skin that would cause electrical shock

• Emergency Exit Windows – Verify all safety windows are operational

• Verify Fire Extinguisher is secure and fully charged

• Test and verify operation and expiration date of Smoke/Fire Detector and Carbon Monoxide Detector (if applicable)

• LP Gas Detector – Verify gas detection and audio alarm and document expiration date of detector

• Verify the rubber grommet is properly sealed around LP gas line of water heater

• Identify the brand, model, and type of refrigerator

• Note the location of the vent panels used by refrigerator

• Operate on all heat sources - 120 volt AC, LP gas and for 3-way refrigerators, 12 volt DC

• Collect serial and model number and verify with manufacturer if recall notice has been issued and completed for this unit

• Visually verify if baffle system on back of refrigerator area is correct and directing heat away from gas coils

• Test for interior temperature of upper and lower refrigerator compartments and ice maker (if installed) *if refrigerator has been operating for minimum of 12 hours

• Check condition of door frame, shelving, crisper drawers, door shelves, door gasket seals, and interior light

• - if equipped

• Identify the brand, model, and type of water heater

• Visually inspect burner assembly and gas exhaust system for blockages and insect infestation

• Fill tank with water (if necessary) and verify operation on all heat sources – LP gas and 120 volt AC if equipped with heating element

• Operate and verify positioning of bypass valves on back of water heater (If installed)

• Determine if proper drain plug has been installed in water heater tank

• Inspect and evaluate if the correct type of dauber screen is being used (If installed)

• - if equipped

• Identify the brand, model, and type of furnace(s) that have been installed (If accessible)

• Identify the type of thermostat controls being used to operate furnace(s)

• Visually inspect air intake and exhaust assemblies for blockages and insect infestation

• Operate and verify warm air discharge out of vents and proper return air flow to unit

• Monitor for unusual noise or vibration of blower motor

• Inspect and evaluate if the correct type of dauber screen is being used (If installed)

• Evaluate and rate the condition of the cooktop or stove, the control knobs, door handles, oven racks, metal grill top, and rubber grommets of top burner area

• List presence and condition of stove top covers

• Verify the ignition and operation of all top burners and the oven flame (if equipped)

• Identify and list the type of cooling unit/heat pump

• Perform cooling efficiency test (Delta T) on each unit

• Visually inspect the plenum box and ductwork sealing, air filter, and the cooling and the heat exhaust coils for debris and cleanliness

• Visually inspect and verify a wash and rinse cycle of the washer and dryer and leaks or damaged hoses

• Evaluate and rate the exterior condition of the dryer exhaust vent

• Identify and list the brand, model, type, and output wattage of the unit

• Verify the rack and turn tables are installed

• Operate unit for 60 seconds utilizing cup of water and then list water temperature

• - if installed

• Identify and list the brand and model of unit

• Verify operation of unit and inspect for leaks and non-functioning rotating racks and wash bars

• - if installed

• Identify and list the brand and model of unit

• Verify the operation and visually inspect the various components

• - if installed

• Identify and list the brand and model of unit

• Operate and verify the various heat settings, fan speed levels, and the back lighting

• Operate and verify condition of the exhaust function and fan speeds

• Visually inspect the filter, lighting, and the exterior condition of the exhaust vent

• Visually inspect the condition of the blades and motor

• Operate and verify condition of the blade direction and fan speeds and lighting (if equipped)

• Visually inspect all ceilings, walls, interior doors, and flooring for signs of water intrusion, surface damage and/or staining

• Operate all windows and doors noting any deficiencies or missing components

• Evaluate the window coverings

• Operate all interior, exterior and décor lighting - 12 volt and 120 volt

• Inspect and evaluate all cabinet doors, drawers, and pull-out operation

• Visually inspect all counter tops and flat surface areas of the kitchen, living room, bathroom, bedroom and storage areas for scratches and damage

• Identify and list all broken and loose cabinet and closet hardware

• Note if appearance of previous damage repairs have been performed

• Visually inspect the condition of the dinette table/booth, chairs, recliners and sofa

• Inspect and note furniture fabric tears, discoloration and signs of excessive wear

•  Visually inspect and note signs of mattress damage or staining

• – if item installed

• Visually inspect and operate all TV, stereo equipment, DVD/disc players, radios, local channels antenna, 12 volt DC power signal booster is operational, roof mounted antenna and remotes

• Visually inspect and evaluate the glass panels, curtains, soap dish areas, seals around the framework and doors for water leaks, latch system

• Type and number of axles and weight ratings for each axle set

• Inspect the frame, axles, springs, rims, and other components for rust, oil stains and visible damage

• Document the information on the tires as to their age and weight capacities

• Check tire pressure and tread condition

• Note any valve extensions and pressure monitors

• Inspect and identify the type of system used to tow vehicle

• Evaluate and list modifications to hitch system